7 English reviews written for Fillamentum PLA Crystal Clear
17 customer reviews in all languages
| 5 stars | | 30 | (66%) |
|---|---|---|---|
| 4 stars | | 6 | (13%) |
| 3 stars | | 4 | (8%) |
| 2 stars | | 1 | (2%) |
| 1 Stars | | 4 | (8%) |
Filter reviews:
-
Luca
May 13 2023
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Was this rating helpful? (0) (0)
-
Will Lockwood
November 17 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 2 out of 5 stars.
Fillamentum PLA Crystal Clear
I must admit to being disappointed with the colour - looked great on the spool but the print was not a Crystal clear as I had hoped and looks a bit Smokey yellow - but it print really well
Was this rating helpful? (0) (0)
-
Tobias
January 01 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 1 out of 5 stars.
Not Reliable: This Filament is Way too Brittle.
Without a doubt, the look of the material is great. Yet, as soon as you touch it, you notice how brittle it is. If you slightly bend it, it breaks.
I printed two spools of this Filament, and 50% of the prints failed because the filament blocked the printer head. In the extruder, chipped off parts of the filament got crammed into the cold end. If I tried to remove the filament, it broke off, so I had to disassemble the extruder to remove the filament bit manually which was stuck there.
The common printing temperature of 215ºC for PLA, even in the specified range for this filament, is too low for faster extrusions (fill). I usually had to increase the nozzle temperature to 225º-230ºC to get normal extrusions on fills.
If the product would be marketed as speciality Filament for art prints but explained the difficult conditions, I would give more stars. But Filamentum writes "Easy to work with at high print speeds" and
"User-friendly for both, home and office environments", which is in my opinion a lie. It requires a high amount of experience to work with this Filament.Was this rating helpful? (8) (1)
-
Alessandro
November 14 2020
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 1 out of 5 stars.
Nightmare to print with Prusa
I've had a lot of problems using this filament with my Prusa MK3S.
I've managed to print at 230, temperature below that cause the filament get stucked inside the extruder after 10 minutesduring the print.
Also, 230 works fine if your print takes less than 5 h, if takes longer you'll end up with the same problem.
I've managed to do have two successful print of 4h each, then the 3rd one the filament got stucked again around 80% of the print.
The only way to clean the extruder is by removing the nozzle and pushing another one from the topWas this rating helpful? (6) (0)
-
Jason Benham
July 23 2020
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 5 out of 5 stars.
Chichester
Excellent product, creates good quality prints with fine detail.
Was this rating helpful? (3) (0)
-
Roderick
May 20 2019
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 5 out of 5 stars.
Review written by Roderick
Excellent product
Was this rating helpful? (1) (2)
-
Customer
October 09 2018
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 5 out of 5 stars.
Review written by Customer
good
Was this rating helpful? (1) (1)
Magazine Articles:
-
Delivery in 3 business days.
More than 10.300 products
We deliver worldwide to
more than 40 countriesSecure payments
with SSL encryption technology
Rated with 3 out of 5 stars.
nice effect and
I'd say that PET budget filament I got on Amazon, prints far lots better than this PLA. Sovol SV06 printer. It easily cogs the printer and have mediocre adhesion. The best Fillamentum I tried so far (and the last)